Question 1

In a(n)  ____ joint the edge of a piece of metal is placed on the surface of another piece of metal.

Accepted Answer

A)   tee
B)   lap
C)   outside corner
D)   edgeE) A) and B)
F) A) and C)

Question 2

The term ____________________ refers to the way pieces of metal are put together or aligned with each other.

Accepted Answer

The answer of The term ____________________ refers to the way...

Question 3

​The terms arrow side, other side, and both sides are used to indicate the ____.

Accepted Answer

A)   ​weld location with respect to the joint
B)   ​dimensions of the part
C)   ​type of joint
D)   ​root openingE) B) and D)
F) B) and C)

Question 4

How might joint design influence welding cost?

Accepted Answer

Almost any weld can be made in any mater...

Question 5

On thin sections it is often possible to make full penetration welds using a(n)  ____ joint.

Accepted Answer

A)   square butt
B)   lap
C)   tee
D)   outside cornerE) All of the above
F) A) and B)

Question 6

​What type of edge preparation for a butt joint on a thick section of magnesium would need to be made?

Accepted Answer

A)   ​U-groove
B)   ​Single bevels
C)   ​V-groove
D)   ​Back gougingE) A) and D)
F) B) and D) A

Question 7

Holes in the other side member of a joint for plug welding are indicated by placing the weld symbol ____ the reference line.

Accepted Answer

A)   above and below
B)   next to
C)   below
D)   aboveE) A) and B)
F) C) and D)

Question 8

​The forces causing stresses in welded joints are ____.

Accepted Answer

A)   ​joint position, layout, base metal, and groove type
B)   ​tensile, compression, bending, torsion, and shear
C)   ​tensile, stretching, heat, and penetration
D)   ​tensile, velocity, chemistry, stretch, and compressionE) A) and B)
F) B) and C)

Question 9

If the weld is to be deposited on the other side of the joint (far side) , the weld symbol is placed ____ the reference line.

Accepted Answer

A)   next to
B)   above and below
C)   below
D)   aboveE) None of the above
F) B) and D)

Question 10

In a(n)  ____ joint the edges of the metal overlap so the thickness of the joint is approximately equal to the combined thickness of both pieces of metal.

Accepted Answer

A)   tee
B)   lap
C)   outside corner
D)   edgeE) C) and D)
F) B) and C) B

Question 11

For most welding processes, plates that are thicker than ____ may be grooved on both the inside and outside of the joint.

Accepted Answer

A)   1/4 inch
B)   3/8 inch
C)   1/2 inch
D)   5/8 inchE) A) and C)
F) B) and C)

Question 12

Which of the following is true about grooves?

Accepted Answer

A)   There are six groove types.
B)   The groove may not be cut with a saw.
C)   The groove can only be made on one plate.
D)   Joint strengths can be improved by making a groove preparation before the joint is welded.E) All of the above
F) B) and C)

Question 13

​What does the term faying surface relate to?

Accepted Answer

A)   ​The surface of a joint that will be melted during the weld.
B)   ​The frayed edges of welder's pants, shirt, or other clothing.
C)   ​The surface that cannot be seen directly such as the inside of a pipe weld joint.
D)   ​It is the outside of the pipe or sides of a weld joint that have been cleaned for welding.E) A) and B)
F) A) and C) C

Question 14

List the reasons for preparing the faying surfaces for welding.

Accepted Answer

Reasons for preparing the faying surface...

Question 15

The size of the root face is important to ensure good ____________________.

Accepted Answer

The answer of The size of the root face is...

Question 16

The strength of spot welds is shown as the minimum shear strength in pounds (newtons)  per spot and is shown ____ the weld symbol.

Accepted Answer

A)   to the left of
B)   to the right of
C)   above
D)   belowE) A) and C)
F) B) and C)

Question 17

Plates in the flat position are usually ____ unless they can be repositioned or are required to be welded on both sides.

Accepted Answer

A)   not grooved
B)   grooved on both sides
C)   grooved on only one side
D)   grooved with a single bevelE) A) and B)
F) B) and C)

Question 18

​Which of the following would not be found on a welding symbol?

Accepted Answer

A)   ​length of the weld and height of reinforcement
B)   ​filler metal and number of welds
C)   ​weld shape and location
D)   ​type of metal and color of paint to be usedE) B) and C)
F) B) and D)

Question 19

In a(n)  ____ joint the edges of the metal are brought together at an angle, usually around 90 degrees to each other.

Accepted Answer

A)   butt
B)   tee
C)   outside corner
D)   edgeE) A) and B)
F) All of the above

Question 20

____________________ are a shorthand language for the welder.

Accepted Answer

The answer of ____________________ are a shorthand language for the...

Exam 22: Welding Joint Design and Welding Symbols

In a(n) ____ joint the edge of a piece of metal is placed on the surface of another piece of metal.

Correct AnswerverifiedShow Answer

The term ____________________ refers to the way pieces of metal are put together or aligned with each other.

Correct AnswerverifiedShow Answer

​The terms arrow side, other side, and both sides are used to indicate the ____.

Correct AnswerverifiedShow Answer

How might joint design influence welding cost?

Correct AnswerverifiedAlmost any weld can be made in any mater...View AnswerShow Answer

On thin sections it is often possible to make full penetration welds using a(n) ____ joint.

Correct AnswerverifiedShow Answer

​What type of edge preparation for a butt joint on a thick section of magnesium would need to be made?

Correct AnswerverifiedA

Holes in the other side member of a joint for plug welding are indicated by placing the weld symbol ____ the reference line.

Correct AnswerverifiedShow Answer

​The forces causing stresses in welded joints are ____.

Correct AnswerverifiedShow Answer

If the weld is to be deposited on the other side of the joint (far side) , the weld symbol is placed ____ the reference line.

Correct AnswerverifiedShow Answer

In a(n) ____ joint the edges of the metal overlap so the thickness of the joint is approximately equal to the combined thickness of both pieces of metal.

Correct AnswerverifiedB

For most welding processes, plates that are thicker than ____ may be grooved on both the inside and outside of the joint.

Correct AnswerverifiedShow Answer

Which of the following is true about grooves?

Correct AnswerverifiedShow Answer

​What does the term faying surface relate to?

Correct AnswerverifiedC

List the reasons for preparing the faying surfaces for welding.

Correct AnswerverifiedReasons for preparing the faying surface...View AnswerShow Answer

The size of the root face is important to ensure good ____________________.

Correct AnswerverifiedShow Answer

The strength of spot welds is shown as the minimum shear strength in pounds (newtons) per spot and is shown ____ the weld symbol.

Correct AnswerverifiedShow Answer

Plates in the flat position are usually ____ unless they can be repositioned or are required to be welded on both sides.

Correct AnswerverifiedShow Answer

​Which of the following would not be found on a welding symbol?

Correct AnswerverifiedShow Answer

In a(n) ____ joint the edges of the metal are brought together at an angle, usually around 90 degrees to each other.

Correct AnswerverifiedShow Answer

____________________ are a shorthand language for the welder.

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

The terms arrow side, other side, and both sides are used to indicate the ____.

Correct Answer
verified

Correct Answer
verified
Almost any weld can be made in any mater...
View Answer

Correct Answer
verified

What type of edge preparation for a butt joint on a thick section of magnesium would need to be made?

Correct Answer
verified
A

Correct Answer
verified

The forces causing stresses in welded joints are ____.

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
B

Correct Answer
verified

Correct Answer
verified

What does the term faying surface relate to?

Correct Answer
verified
C

Correct Answer
verified
Reasons for preparing the faying surface...
View Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Which of the following would not be found on a welding symbol?

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified